Classic Simplicity, Compact, and Timeless Reliability
The IC-718 is a compact rig with ample features for HF communications. The HF bands enable you to communicate across long distances, even reaching the other side of the Earth. With its wide dynamic range, high S/N ratio, and full duty operation, you will make contacts easily. Experience the combination of RF and digital technology and you will realize the IC-718 is the most practical rig for your needs.
Front Mounted Speaker
The IC-718 has a speaker mounted on the front panel. With the speaker facing the operator, audio sounds can be clearly heard without impediment during operation.
Superior Basic Performance
The IC-718 has 0.03 ~ 29.999999 MHz* general coverage receive capability. A 4-element system is employed for the 1st receive mixer, providing superior receive IMD, especially from in-band near-by interfering signals. A well-designed double-conversion system to help minimize image and spurious responses for better signal fidelity, is also built-in. Its PLL circuit improves C/N ratio characteristics. PLL circuit has been adopted to improve C/N ratio characteristics. The combination of the 4-element system mixer and new PLL circuit allows superior basic performance as that of a commercial grade transceiver.
* Guaranteed range: 0.5 ~ 29.999999 MHz.
Noise Reduction Function*
The Noise Reduction pulls desired AF signals from noise. Outstanding S/N ratio is achieved, providing clean audio in SSB and AM.
*Depending on version.
Automatic Notch Out of the Filter*
The Notch Filter function automatically minimizes beat signals and heterodynes while preserving the received signal. Also, the notch frequency is automatically adjusted to follow interfering beat signals. For example, reducing interference from RTTY signals during SSB operation.
*Depending on version.
Interference Rejection — IF Shift
To reject interference, the IC-718 has an IF Shift function which shifts the center frequency of the IF passband electronically to reduce adjacent interference.
Microphone Compressor
The IC-718 has a low distortion microphone compressor. This feature compresses microphone audio input to increase average audio output level. The result is that talk power is increased. This function is effective for long distance communication, or when propagation conditions are poor.
RF Gain Control
The RF gain adjusts minimum response receiver gain and ignores signals weaker than the preset level — providing pleasant standby or scanning operation. It is combined with the squelch control.
Ample CW Features
An electronic keyer with a variable dot/dash ratio (2.8:1 to 4.5:1) control is built in. By simply connecting a paddle, easy CW operation can be made. The CW pitch and the key speed are also variable from 300 ~ 900 Hz, 6 ~ 60 wpm, respectively. Of course, full break-in capability is available with an adjustable break-in delay.
Easy VOX Operation
A VOX (voice operated transmission) is included with the IC-718. It provides hands-free operation by detecting audio signals from the microphone.
Five Selectable IF Filter Widths
6 kHz: Wide standard filter
2.4 kHz: Normal (Narrow for AM) standard filter
The FPGA (Field Programmable Gate Array) digital filtering system has been adopted. Two standard IF widths are available, and a third width can be selected from five to suit your style of operation and no need to purchase a filter.
Digital S/RF Meter
Built-in multi-functional digital S/RF meter indicates signal strength level while receiving, and either transmit output power, ALC level or VSWR ratio while transmitting.
Simple Operation
The IC-718 is equipped with a minimum number of buttons and knobs for superior feature selectability. Use the 10-key pad on the front panel to directly enter an operating frequency, or a memory channel number. The auto tuning steps function helps quick tuning activates when quickly turning the dial. And the band stacking register is very convenient when changing operating bands.
Optional Automatic Antenna Tuner
The optional automatic antenna tuner, AH-730 performs tuning operations at a high speed of about 2 to 3 seconds. When you change the operation band, band information is transferred to the tuner and automatically matches to the antenna.
Optional Automatic Tuning Antenna AH-740
The optional vehicle mount automatic tuning antenna provides relay-driven highspeed tuning from 2.5 to 30 MHz. Its IP55 dust-protection and water jet resistance ensures reliable operation in harsh weather conditions.
Other Features
• USB, LSB, CW, RTTY (FSK) and AM modes are built-in
• Level adjustable noise blanker
• RF attenuator and Pre-amplifier
• A variety of scanning function types
• At total of 101 memory channels
• A hand microphone is supplied
Rear Panel View
General
| Frequency coverage (Differs according to version) |
Rx | 0.030 ~ 29.999 MHz*1 |
|---|---|---|
| Tx | 1.800 ~ 1.999*2, 3.500 ~ 3.999*2, 7.000 ~ 7.300, 10.100 ~ 10.150, 14.000 ~ 14.350, 18.068 ~ 18.168, 21.000 ~ 21.450, 24.890 ~ 24.990, 28.000 ~ 29.700 MHz |
|
| Mode | USB, LSB, CW, RTTY (FSK), AM | |
| Frequency resolution | 1 Hz | |
| Frequency stability | Less than ±200 Hz from 1 min. ~ 60 min. after power ON Less than ±30 Hz/hour at +25˚C (+77˚F) 1 hour later after power ON Less than ±350 Hz between 0˚C ~ +50˚C (+32˚F ~ +122˚F) |
|
| Maximum current drain | 20 A at 13.8 V DC | |
| Power supply requirement | 13.8 V DC ±15 % | |
| Antenna connector | SO-239 (50 Ω unbalanced) | |
| Number of memory channels | 101 (99 regular, 2 scan edges) | |
| Power consumption | Rx | 1.3 A (Standby), 2.0 A (Maximum audio) |
| Tx | 20 A (at 100 W output power) | |
| Operating temperature range | –10˚C ~ +60˚C, 14˚F ~ 140˚F | |
| Dimensions (W×H×D; projections are not included) | 240 × 95 × 239 mm, 9.4 × 3.7 × 9.4 in | |
| Weight (Approximately) | 3.8 kg, 8.4 lb | |
*1 Guaranteed range 0.5 ~ 29.999 MHz. *2 Varies according to version.
Transmitter
| Output power | SSB, CW, RTTY | 2 ~ 100 W |
|---|---|---|
| AM | 2 ~ 35 W | |
| Modulation system | SSB | Balanced modulation |
| AM | Low level modulation | |
| Spurious emissions | Less than –50 dB below peak output power | |
| Carrier suppression | More than 40 dB | |
| Unwanted sideband | More than 50 dB | |
| Microphone impedance | 8-pin connector (600 Ω) | |
Receiver
| Receiver system | Double-conversion superheterodyne | |
|---|---|---|
| Sensitivity (at 10 dB S/N) (For all versions) |
SSB, CW, RTTY | 0.16 μV (1.8 ~ 29.999 MHz) |
| AM | 13 μV (0.5 ~ 1.799 MHz) 2 μV (1.8 ~ 29.999 MHz) |
|
| Selectivity | SSB, CW, RTTY | More than 2.1 kHz / –6 dB Less than 4.5 kHz / –60 dB |
| AM | More than 6.0 kHz/–6 dB Less than 20 kHz / –40 dB |
|
| Squelch sensitivity (Threshold) | Less than 5.6 μV (SSB) | |
| Spurious and image rejection | More than 70 dB (1.8 ~ 29.999 MHz) | |
| Audio output power | More than 2.0 W (at 10 % distortion with an 8 Ω load) | |
| External speaker connector | 2-conductor 3.5 (d) mm (1/8) / 8 Ω | |
The LCD display may have cosmetic imperfections that appear as small or dark spots. This is not a malfunction or defect, but a normal characteristic of LCD displays.
All stated specifications are subject to change without notice or obligation.
Applicable U.S. Military Specifications
| Standard |
MIL 810 F | |
|---|---|---|
| Method | Procedure | |
| Temperature Shock |
503.4 |
I |
| Rain Drip* |
506.4 |
III |
| Vibration |
514.5 |
I |
| Shock |
516.5 |
I, IV |
*Rain Drip test was performed on the front panel only. Also meets equivalent MIL-STD-810-C, -D and -E.
Supplied Accessories
- Hand microphone
- DC power cable
- Spare fuses
(May differ depending on the version)
MICROPHONES
EXTERNAL SPEAKERS
MOUNTING BRACKETS
CARRYING HANDLES
ANTENNAS
ANTENNA TUNERS
ADAPTER CABLES
Catalogs / Brochures
| Brochures Name | Size |
|---|---|
| HAM Radios and Receivers | 3.28MB |
| IC-718_LT | 1,004KB |
Instruction Manual / Guides
| Name | Model Name | Note |
|---|---|---|
| BASIC MANUAL | IC-718 | |
| ADVANCED MANUAL | IC-718 |
Firmware / Software
| Type | Model Name | Version | Last Update |
|---|---|---|---|
| Firmware | IC-PW2 | Version 1.30 | 2025.04.30 |
CloseCloseIngress Protection (IP) Code
Ingress Protection (IP) ratings define the level of protection provided by enclosures to prevent the ingress of foreign objects (dust) and liquid into the electrical equipment.
International Standard IEC 60529 outlines an international classification system that describes the sealing characteristics of electrical equipment.
The classification system uses the “IP” code, or “Ingress Protection” code, to define the level of seal.
An IP number contains two numbers (i.e. IP67) in most instances which relate to the level of protection provided by an enclosure or housing.
Either number may be shown as “X” (i.e. IPX6 / IP7X) to indicate the “X” part is not tested.
Degrees of Solid Particle Protection – 1st Digit
| IP6x | No ingress of dust; complete protection against contact. (Dust tight) |
|---|---|
| IP5x | Protected from the amount of dust that would interfere with normal operation. (Dust protected) |
Degrees of Liquid Ingress Protection – 2nd Digit
| IPx8 | Protected against continuous immersion in water. Depth and duration specified by model. |
|---|---|
| IPx7 | Protected against temporary immersion in water for 1 m (3.3 ft) for 30 minutes |
| IPx6 | Protected against water projected by powerful jets from any direction. 100 L per minute by a powerful jets (12.5 mm) for 3 minutes. |
| IPx5 | Protected against water projected by jets from any direction. 12.5 L per minute by a nozzle (6.3 mm) for 3 minutes. |
| IPx4 | Protected against water splashed against the equipment from any direction |
