- 146–174, 400–430, 450–480MHz
- 5W output power (100% duty cycle)
- Repeater or base operation
- 1U 19-inch rack mountable
- 6 programmable function keys
- Two-digit LED display
- 30 channel scanning base (Conventional mode)
- 3W external speaker audio
- Program/modem interface
- Remote terminal interface
- DTMF AUX output control
- DTMF AUX input monitoring
- Programmable AUX I/O's
- Flash firmware upgrading
- 16 CTCSS and DTCS built-in
- Digital conventional mode
- Multi-site conventional
- NXDN™ Type-C trunking mode
- Digital/analog mixed mode operation
- 15-bit digital scrambler
- 6.25 & 12.5 kHz channels
- Unit ID & Group ID validation
- Optional OCXO unit for 6.25kHz channel spacing
- Up to 48 site trunked IP network
- IP network connectivity
- Compact flash memory expansion
* Some features require activation licenses.
Type-C Multi-site Trunking
Multi-site Conventional System
With the IC-FR5000C series, up to 16 or 48 repeaters can be interlinked with each other*.
|Number of channels||30 channels|
|Type of emission||11K0F3E, 8K30F1E/F1D/F7W,
|Antenna impedance||50Ω (Type-N)|
|Operating temperature range||−30°C to +60°C; −22°F to +140°F|
|Power supply voltage||10.8–15.9V DC nominal|
|Dimensions (W×H×D)||483×44×331 mm; 19.02×1.73×13.03 in|
|Weight||5kg; 11.02 lb (approximately)|
100% duty cycle
|Spurious emissions||73dB typ.|
|FM hum and noise||50dB typ. (Narrow)|
|Audio distortion||Less than 1% (at 1000Hz)|
|Sensitivity||Analog||0.30μV typ. (at 12dB SINAD)|
|Digital||0.33/0.27μV typ. (D 12.5kHz/D 6.25kHz, at 3% BER)|
|Adjacent channel selectivity||85dB typ. (Narrow)||81dB typ. (Narrow)|
|Spurious response||100dB typ.|
|Intermodulation distortion||85dB typ. (Narrow)|
|Hum and noise ratio||55dB typ. (Narrow)|
|Audio output power||3W typ. (External SP, at 5% distortion with 4Ω load)|
All stated specifications are subject to change without notice or obligation.
- DC power cable connector
Ingress Protection (IP) Code
Ingress Protection (IP) ratings define the level of protection provided by enclosures to prevent the ingress of foreign objects (dust) and liquid into the electrical equipment.
International Standard IEC 60529 outlines an international classification system that describes the sealing characteristics of electrical equipment.
The classification system uses the “IP” code, or “Ingress Protection” code, to define the level of seal.
An IP number contains two numbers (i.e. IP67) in most instances which relate to the level of protection provided by an enclosure or housing.
Either number may be shown as “X” (i.e. IPX6 / IP7X) to indicate the “X” part is not tested.
Degrees of Solid Particle Protection – 1st Digit
|IP6x||No ingress of dust; complete protection against contact. (Dust tight)|
|IP5x||Protected from the amount of dust that would interfere with normal operation. (Dust protected)|
Degrees of Liquid Ingress Protection – 2nd Digit
|IPx8||Protected against continuous immersion in water.
Depth and duration specified by model.
|IPx7||Protected against temporary immersion in water for 1 m (3.3 ft) for 30 minutes|
|IPx6||Protected against water projected by powerful jets from any direction.
100 L per minute by a powerful jets (12.5 mm) for 3 minutes.
|IPx5||Protected against water projected by jets from any direction.
12.5 L per minute by a nozzle (6.3 mm) for 3 minutes.
|IPx4||Protected against water splashed against the equipment from any direction|