Tough and Waterproof License Free Radio for Professional Use
The IC-V10MR can be used under hard rain, and you can also wash the radio with clean water as instructed in the user manual.
Drop Test Durability
The IC-V10MR exceeds MIL-STD specifications and has passed more difficult drop tests (1.5 m; 4.9 ft x 6 surfaces) than specified for professional use.
Large Sound for Clear Audio
The combination of a custom high capacity speaker and large sound space in front of the speaker delivers a powerful 1500 mW audio with exceptional listening clarity.
Built-in Motion Sensor
Compact Size to Fit Your Palm
The radio size is a perfect fit at just 2.1 inches wide and 1.0 inches deep. And the weight is only 8.5 oz even when the battery pack is attached.
Signaling for Selective Call
2-Tone, MDC, CTCSS and DTCS capabilities to use selective call and reject un-intended calls for quiet stand-by.
Large Capacity Battery for Long Operation
A low power consumption design and the supplied 1570 mAh Lithium-Ion battery allow use of the radio for more than 16 hours*.
*5:5:90 duty ratio for transmit: receive: stand-by (with power save function)
- VOX function for hands-free operation
- Audio compander
- Siren sound for security alarm
- Surveillance function temporarily turns OFF the beep and LED indicator
- Emergency call with open microphone function
- Automatic scan
250,000 sq ft
in a building*
in a building*
in a work site*
Communication range may differ depending on operating environment or weather conditions, etc.
|Usable Frequencies and (bandwidth)||
151.820 MHz (11.25 kHz), 151.880 MHz (11.25 kHz),
|Number of Memory channels||16 ch|
|Transmit output power||2 W (High), 1 W (Mid), 0.5 W (Low)|
|Receiver sensitivity||0.25 μV (typical) for 12 dB SINAD|
|Squelch sensitivity||0.25 μV (typical) at squelch threshold point|
|Audio output power
(at 5% distortion, 8 Ω load)
|Internal SP 1.5 W (typical)
External SP 0.4 W (typical)
|Antenna impedance||50 Ω|
|Power supply Voltage||7.5 V|
|Current drain||Receive stand-by 77 mA
Receive max. audio 500 mA
Transmit (High) 0.9 A
|Dimensions (with BP-279)||52.2 (W) × 111.8 (H) × 24.5 (D) mm
2.1 (W) × 4.4 (H) × 1.0 (D) inches
|Weight (with BP-279)||240 g; 8.5 oz (approximate)|
All stated specifications are subject to change without notice or obligation.
Measurements made in accordance with TIA-603.
Applicable U.S. Military Specifications
(radio specifications are not changed after each test)
|Keep the transceiver 20℃/101.3 kPa and
25℃/57.2 kPa for a total of 7 hours
|Keep the transceiver between 30 to 63℃ for a total of 168 hours|
|Keep the transceiver at -25℃ for 4 hours|
|Keep the transceiver at -51℃/2 h and +71℃/2 h × 3 cycles (total 12 hours)|
|Keep the transceiver at 49℃ and 1120 W/m2 for 24 h × 3 cycles (for a total of 72 hours)|
|I : Blast 1.7 mm/min rain with 18 m/s wind for
30 min to 6 surfaces (for a total of 180 min)
III: Drip water 2800 l/m2/h for 15 min.
|Keep the transceiver at 95% humidity with 30℃ and 60℃ for 240 hours.|
|Spray 5% salt water with 1-3 ml/h at 80 cm 2 under 35℃/95% condition for 24 hours then dry it under 24℃/50% condition × 2 cycles|
|Blowing talc powder Temp/time: 23℃/6 h and 60℃/6 h, humidity: less than 30%, wind speed: 8.9 m/s, powder density: 10 ±7 g/m3|
|Keep the transceiver in pure water for 1 m / 30 min.|
|I||Vibrate the transceiver at each 3 axis (X, Y, Z), frequencies 5 – 500 Hz, 1.05 G for 1 hour|
|When packing, drop 1.22 m height for
6 surfaces, 8 corners, 12 edges (total 26 drops)
Also meets equivalent MIL-STD-810-C, -D, -E and -F.
- Battery pack, BP-279
- Belt clip, MB-133
- Rapid charger, BC-213
- AC adapter, BC-242
- Antenna, FA-SC28V
The AD-130 charger adapters are supplied.
AC adapter supplied depending on versions.
POWER SUPPLY CABLES
Ingress Protection (IP) Code
Ingress Protection (IP) ratings define the level of protection provided by enclosures to prevent the ingress of foreign objects (dust) and liquid into the electrical equipment.
International Standard IEC 60529 outlines an international classification system that describes the sealing characteristics of electrical equipment.
The classification system uses the “IP” code, or “Ingress Protection” code, to define the level of seal.
An IP number contains two numbers (i.e. IP67) in most instances which relate to the level of protection provided by an enclosure or housing.
Either number may be shown as “X” (i.e. IPX6 / IP7X) to indicate the “X” part is not tested.
Degrees of Solid Particle Protection – 1st Digit
|IP6x||No ingress of dust; complete protection against contact. (Dust tight)|
|IP5x||Protected from the amount of dust that would interfere with normal operation. (Dust protected)|
Degrees of Liquid Ingress Protection – 2nd Digit
|IPx8||Protected against continuous immersion in water.
Depth and duration specified by model.
|IPx7||Protected against temporary immersion in water for 1 m (3.3 ft) for 30 minutes|
|IPx6||Protected against water projected by powerful jets from any direction.
100 L per minute by a powerful jets (12.5 mm) for 3 minutes.
|IPx5||Protected against water projected by jets from any direction.
12.5 L per minute by a nozzle (6.3 mm) for 3 minutes.
|IPx4||Protected against water splashed against the equipment from any direction|