Discontinued ProductNote: The contents of this page is as of the time it was created.
VHF AND UHF DIGITAL REPEATERS
Fanless dPMR™ Digital Repeater
Reliable 50 W Full Duty Operation
- VHF/IDAS DIGITAL IC-FR5200H (dPMR Version)
- UHF/IDAS DIGITAL IC-FR6200H (dPMR Version)
50W 100% Duty Cycle Operation
Employing a high performance power amplifier, together with the solid heatsink built into the chassis, the IC-FR5200H series provides 50W output at 100% duty cycle operation. No internal cooling fan required.
dPMR™ Mode 3 Digital Trunking
With the external controller, IC-FC5000E, the IC-FR5200H series can be used in a dPMR Mode 3 digital trunking system. A small number of communication channels are automatically and dynamically allocated to accommodate a large number of subscribers. The trunking sites can be interconnected over an IP network.
dPMR™ Mode 2, Analog FM and Mixed Mode
The IC-FR5200H series is compatible with both analog FM mode and dPMR single site conventional mode (Mode 2). Program digital and/or analog FM modes per channel. The mixed mode operation allows you to receive both analog FM and dPMR Mode 2 and to transmit either mode depending on the received signal.
32 Channel Capacity and 5 Programmable Buttons
The 12-digit dot-matrix display, 5 programmable buttons, 32 memory channels and internal speaker allow you to use the repeater as a simple base station or to check repeater activity. LEDs on the front panel show channel conditions.
Multiple CTCSS, DTCS Tone and CC Decode
The IC-FR5200H series decodes multiple CTCSS and DTCS as well as digital CC on a per channel basis (up to 16 tones/codes) and downlinks the received signal with a specified tone/code. This function is useful for sharing a channel with multiple groups.
19-inch Rack Mount, 2U Height Low Profile Design
The IC-FR5200H series uses only 2U height. This low profile configuration allows you to stack multiple units in an industry standard 19-inch rack and provides great space efficiency.
- CW ID transmission
- Digital voice scrambler provides 15-bit key (about 32,000 codes)
- ±0.5ppm high frequency stability
- D-SUB 25-pin accessory connector
- Built-in inversion voice scrambler*
- PTT priority setting (Local Mic., external PTT or repeater operation)
- Built-in audio compander*
- 5-Tone and DTMF encoder/decoder*
- Normal and priority scan
- Low voltage alert
- Key assign stickers supplied
* Analog mode only.
Rear Panel View
|Frequency coverage||136–174 MHz||350–400,
|Number of channels||Max. 32 channels|
|Channel spacing||6.25/12.5/20/25 kHz|
|Type of emission||16K0F3E, 14K0F3E, 8K50F3E,
|Antenna impedance||50Ω (Type-N × 2)|
|Operating temperature range||–30˚C to +60˚C; –22˚F to +140˚F|
|Power supply voltage||13.2 V DC|
(at 13.6V DC)
|RX Max. audio/Stand-by||1.2A/550 mA typ.(LCD backlight OFF)|
|Dimensions (W×H×D)||483×88×360 mm|
|Output power||50 W (adjustable to 5 W)
100% duty cycle (at 20–35˚C, 24 hours)
|Max. frequency deviation||±5.0/±4.0/±2.5 kHz (W/M/N)|
|Spurious emissions||0.25 μW (≤1 GHz), 1.0 μW (>1 GHz)|
|Audio harmonic distortion||1% typ. (40% deviation)|
|Intermodulation attenuation||40 dB min.|
|Digital FSK error||5% Max.|
|Microphone impedance||600 Ω (8-pin modular)|
|Sensitivity||Analog||–10 dBμV max. (12 dB SINAD)|
|Digital||0 dBμV emf. max. (1% BER)|
|Adjacent channel selectivity||(W/M/N)||86/83/75 dB typ.||79/76/71 dB typ.|
|(Digital)||67 dB typ.||63 dB typ.|
|Spurious response||(W/M/N)||80 dB|
|(Digital)||90 dBμV emf|
|Intermodulation rejection||(W/M/N)||75/75/73 dB typ.||72/72/71 dB typ.|
|(Digital)||76 dBμV emf typ.||76 dBμV emf typ.|
|Audio output power||3.5 W min. (5% distortion, 4 Ω load)|
|External speaker connector||2-conductor 3.5 (d) mm (1/8″)/4Ω|
All stated specifications are subject to change without notice or obligation.
Ingress Protection (IP) Code
Ingress Protection (IP) ratings define the level of protection provided by enclosures to prevent the ingress of foreign objects (dust) and liquid into the electrical equipment.
International Standard IEC 60529 outlines an international classification system that describes the sealing characteristics of electrical equipment.
The classification system uses the “IP” code, or “Ingress Protection” code, to define the level of seal.
An IP number contains two numbers (i.e. IP67) in most instances which relate to the level of protection provided by an enclosure or housing.
Either number may be shown as “X” (i.e. IPX6 / IP7X) to indicate the “X” part is not tested.
Degrees of Solid Particle Protection – 1st Digit
|IP6x||No ingress of dust; complete protection against contact. (Dust tight)|
|IP5x||Protected from the amount of dust that would interfere with normal operation. (Dust protected)|
Degrees of Liquid Ingress Protection – 2nd Digit
|IPx8||Protected against continuous immersion in water.
Depth and duration specified by model.
|IPx7||Protected against temporary immersion in water for 1 m (3.3 ft) for 30 minutes|
|IPx6||Protected against water projected by powerful jets from any direction.
100 L per minute by a powerful jets (12.5 mm) for 3 minutes.
|IPx5||Protected against water projected by jets from any direction.
12.5 L per minute by a nozzle (6.3 mm) for 3 minutes.
|IPx4||Protected against water splashed against the equipment from any direction|