IF DSP
The latest IF DSP technology is employed in the IC-7200. While the IC-7200 is an entry-class transceiver, advanced digital features are comparable to higher class transceivers.
AGC Loop Management
Distortion and blocking from strong nearby signals are prevented by placing DSP functions inside the AGC loop. The AGC time constants are selectable from fast, slow and off for each operating mode.
Digital IF Filter
Optional filters will be never required for the IC-7200. The built-in digital filter allows you to flexibly select the filter width and shape from soft and sharp* and provides cuttingedge filter characteristics.
* Filter shape is selectable for SSB and CW modes only.
Digital Twin PBT
Only Icom brings you Twin Passband tuning! Tailor your IF passband with the Twin PBT by electronically shifting the upper and lower edges of the IF filter. Depending on the use of the concentric knobs, you can either narrow the IF passband, or shift the entire passband to eliminate interfering signals.
Manual Notch Filter
The manual notch filter delivers more than 70dB of attenuation. Strong interfering tones will be eliminated without adversely affecting the AGC loop performance. On the bottom right of the front panel, a dedicated control knob adjusts the notch filter frequency.
Digital Noise Reduction
Digital noise reduction reduces background noise and improves the signal-to-noise ratio. The noise reduction level is adjustable in 16 steps. It improves the readability of voice and data signals.
Digital Noise Blanker
The noise blanker reduces pulse-type noise such as engine ignition and sparking. The NB level and width (blanking duration) are adjustable in 100 steps.
High Stability Transmitter
The DDS (Direct digital synthesizer) creates a clear, clean transmit signal and improves the C/N ratio. With a dual-fan cooling system, the IC-7200 provides stable high quality output even during high duty cycle operation.
USB Port for PC Control
The IC-7200 can be controlled by a PC through a USB port using the CI-V data format. In addition, modulator and received audio can also be transferred over the USB cable. By using appropriate external software, you can record incoming call and/or transmit preprogrammed messages from your PC.
RF Speech Compressor
The digital RF speech compressor increases your average talk power in SSB mode. Even when the compression level is increased, the DSP controlled RF speech compressor provides low distortion audio.
CW Mode Operation
Full break-in, selectable CW carrier point (USB or LSB) and adjustable CW pitch are also standard.
Tough Construction Against Water Intrusion
Waterproof protection technologies that are used in Icom’ s marine radios are applied to the buttons and knobs on the front panel to provide a measure of protection against water intrusion.
*IC-7200 is NOT waterproof.
Rugged Design for Outdoor Use
The rugged design of the IC-7200 means your enjoyment of this rig is not limited to your shack only.
Other Features
・ RIT
・ VOX
・ ±0.5ppm frequency stability
・ LCD backlight (Hi/Lo/Off)
・ CI-V interface
・ 201 memory channels
・ Built-in 20dB attenuator
・ Preamplifier
・ Dial lock
・ Auto TS function
・ 1Hz step tuning
・ Band stacking register
・ Built-in voice synthesizer
・ Quick split
・ Front facing speaker
・ Quick set mode
“Rear Bumper”
The “rear bumper” protects various connectors on the rear panel and lets you stand the radio on its rear end when the antenna is disconnected, such as while moving or packing the radio.
General
Frequency coverage*1 (Differs according to version) |
Rx : 0.030–60.000000MHz*2 Tx : 1.800– 1.999999MHz 3.500– 3.999999MHz 5.255– 5.405MHz*3 7.000– 7.300MHz 10.100–10.150MHz 14.000–14.350MHz 18.068–18.168MHz 21.000–21.450MHz 24.890–24.990MHz 28.000–29.700MHz 50.000–54.000MHz |
---|---|
Mode | USB, LSB, CW, RTTY (FSK), AM |
Frequency stability | Less than ±0.5ppm |
Maximum current drain | 22.0A |
Power supply requirement | 13.8V DC ±15 % (negative ground) |
Antenna connector | SO-239 (50Ω) |
Number of memory channels |
201ch (199 regular, 2 scan edges) |
Dimensions (W×H×D; Projections are not included) |
241×84×281 mm 9.49×3.31×11.06 in |
Weight (approx.) | 5.5 kg; 12.1 lb |
*1 Shows USA version. Frequency coverage depends on version.
*2 Guaranteed range: 0.5-29.999 and 50-54.000 MHz.
*3 Some frequency ranges are not guaranteed.
Transmitter
Output power |
SSB, CW, RTTY: |
---|---|
Spurious emissions | Less than –50dB (HF) Less than –63dB (50MHz) |
Carrier suppression | More than 50dB |
Unwanted sideband | More than 50dB |
Microphone connector | 8-pin connector (600Ω) |
Receiver
Sensitivity (10dB S/N, Preamp ON, Filter shape sharp) |
SSB, CW: Less than 0.16μV (1.8–29.995MHz): Less than 0.13μV (50MHz band) AM: Less than 13μV (0.5–1.8MHz) Less than 2μV (1.8–29.995MHz) Less than 1μV (50MHz band) |
---|---|
Selectivity | SSB(BW: 2.4kHz, sharp): More than 2.4kHz/–6dB Less than 3.6kHz/–60dB CW(BW: 500Hz, sharp) : More than 500Hz/–6dB Less than 900Hz/–60dB RTTY (BW: 350Hz): More than 360Hz/–6dB Less than 650Hz/–60dB AM (BW: 6kHz): More than 6.0kHz/–6dB Less than 15.0kHz/–60dB |
Spurious and image rejection |
More than 70dB (Except 1⁄2 IF through on 50MHz band) |
AF power (at 10% distortion with an 8Ω load) |
More than 2.0W |
External speaker connector |
2-conductor 3.5 (d) mm (1⁄8″) /8Ω |
All stated specifications are subject to change without notice or obligation.
MICROPHONES
MOUNTING BRACKETS
CARRYING HANDLES
ANTENNAS
ANTENNA TUNERS
POWER AMPLIFIERS
EXTERNAL DEVICES
ADAPTER CABLES
Catalogs / Brochures
Brochures Name | Size |
---|---|
IC-7200 | 811KB |
Instruction Manual / Guides
Name | Model Name | Note |
---|---|---|
Instruction manual | IC-7200 | |
Advanced Instructions | IC-7200 |
Firmware / Software
Type | Model Name | Version | Last Update |
---|---|---|---|
USB Driver | IC-7100/IC-7200/IC-7300/IC-7410/IC-7600/IC-7610/IC-7850/IC-7851/IC-9100/IC-9700/IC-R8600 | Version 1.30 | 2018.06.07 |
USB Driver | IC-7100/IC-7200/IC-7300/IC-7410/IC-7600/IC-7610/IC-7850/IC-7851/IC-9100/IC-9700/IC-R8600 | Version 1.20 | 2017.10.05 |
USB Driver | IC-7100/IC-7200/IC-7410/IC-7600/IC-9100 | Ver.1.10 | 2018.06.07 |
USB Driver | IC-7200/IC-7600 | Ver.1.00 | 2009.02.26 |
Control software | RS-BA1 Version 2 | Version 2.70 | 2024.08.28 |
Ingress Protection (IP) Code
Ingress Protection (IP) ratings define the level of protection provided by enclosures to prevent the ingress of foreign objects (dust) and liquid into the electrical equipment.
International Standard IEC 60529 outlines an international classification system that describes the sealing characteristics of electrical equipment.
The classification system uses the “IP” code, or “Ingress Protection” code, to define the level of seal.
An IP number contains two numbers (i.e. IP67) in most instances which relate to the level of protection provided by an enclosure or housing.
Either number may be shown as “X” (i.e. IPX6 / IP7X) to indicate the “X” part is not tested.
Degrees of Solid Particle Protection – 1st Digit
IP6x | No ingress of dust; complete protection against contact. (Dust tight) |
---|---|
IP5x | Protected from the amount of dust that would interfere with normal operation. (Dust protected) |
Degrees of Liquid Ingress Protection – 2nd Digit
IPx8 | Protected against continuous immersion in water. Depth and duration specified by model. |
---|---|
IPx7 | Protected against temporary immersion in water for 1 m (3.3 ft) for 30 minutes |
IPx6 | Protected against water projected by powerful jets from any direction. 100 L per minute by a powerful jets (12.5 mm) for 3 minutes. |
IPx5 | Protected against water projected by jets from any direction. 12.5 L per minute by a nozzle (6.3 mm) for 3 minutes. |
IPx4 | Protected against water splashed against the equipment from any direction |