Firmware Download

Download the old version

Download Type Firmware
Model name IC-705
Version Version 1.26
Update 2021/07/09
Major changes
  • Changes from Version 1.24

- When in the Center mode of the Spectrum scope screen, the REF level setting does not reflect the scope waveform during transmission.

  • - This firmware update version 1.26 has been improved, so it will not reset settings and memories.
  • If the firmware is updated from version 1.24 or earlier, the settings and memories are not reset. 
  • However, if the firmware is reverted to 1.26 from a later version (after 1.26), the settings and memories may be reset.
Note

You cannot revert to firmware version 1.24 or earlier on the serial numbers listed below, which have firmware version 1.26 or later installed.

IC-705    #32: Serial number 32001001 or later
IC-705    #33: Serial number 33001001 or later
IC-705-T  #36: Serial number 36001001 or later
IC-705    #37: Serial number 37001001 or later

Please note on the models listed above, if you revert to firmware version 1.24 or earlier, the audio will not be correctly output.


The CS-705 programming software used with this firmware can be downloaded here.

  • To update the firmware
  • 1. Download and unzip the firmware data (for example, 705E126.dat) and copy it into the “IC-705” folder that is on your microSD card.
  • 2. Insert the microSD card with the firmware data into the transceiver. 
  • 3. Update the firmware.
  • 3-1. Display the SD CARD screen in the Menu. 
  • 3-2. Touch “Firmware Update” on the SD CARD screen to open the FIRMWARE UPDATE screen.
  • 3-3. Touch [▼] to scroll to the end of the screen to read all the precautions, after you read and agree with all the precautions, touch [YES]. 
  • 3-4. The confirmation dialog recommends making a backup of the settings and memories, touch [YES]. 
  • We recommend that you make a backup of them in this step, because all the settings and memories may be reset after updating the firmware.
  • 3-5. After the backup file is made, and the firmware selection screen is displayed, touch the firmware update data (for example, 705E126). 
  • 3-6. Please carefully read all the precautions, and when you want to execute it, touch [Yes] for 1 second to start the firmware update.
  • 3-7. When the update is completed, "Firmware updating has completed.” is displayed, and the transceiver will automatically restart.
  • If the setting data needs to be converted, it may take some time to restart. 
  • 4. If the settings and memories have been reset, load the settings and memories that have been backed up onto the microSD card.
  • 4-1. Display the SD CARD screen in the Menu.
  • 4-2. Touch “Load Setting” on the SD CARD screen to open the LOAD SETTING screen. 
  • 4-3. Touch the file name of the saved file. 
  • 4-4. Touch “ALL,” and then the dialog “Keep ‘SKIP’ settings in the Repeater List?” is displayed, touch [YES].
  • 4-5. The dialog "Load file? The new “REF Adjust” setting will be saved.” is displayed, touch [Yes].
  • 4-6. After the loading ends, “COMPLETED! Restart the IC-705.” is displayed, restart the transceiver. 
  • After updating the firmware, the Version Information in the OTHERS Set will be as follows.
  • Main CPU: 1.26
  • Sub CPU: 1.01
  • DSP Program: 1.11
  • DSP Data: 1.00
  • FPGA: 1.01
  • DV DSP: 1.02
  • GPS: 13196
  • Bluetooth: 1.12
  • WLAN: 2.0.0.0_2.2.0.7_3.17.0.4
File Size 8.17MB
File Type zip
Manual manual download page

Regarding this Download Service.

When using this download service, the implementation, use and/or results of use are the sole responsibility of you using this download service and the equipment. You shall comply with applicable laws and regulatory requirements in the use of this download service and in the operation of the equipment.

Firmware is important data for the basic system control of your equipment. An interruption during downloading or a malfunction may cause a failure in the data re-writing, and your equipment may stop functioning normally. If such a failure of the firmware re-writing results in your equipment not functioning normally, Icom Inc. and its affiliates expressly denies and is free from any and all responsibility arising from the result of damage from such an event.

You agree not to hold Icom Inc. and its affiliates responsible for any damage to your equipment operation or loss of data, or unauthorized use of the equipment, whether intentional or not, as a result of use this download service.